manualshive.com logo in svg

Thermo Scientific 42iQTL, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific 42iQTL Скачать руководство пользователя страница 115

Operation 

Settings 

Thermo Scientific 

42iQTL Instruction Manual     

3-89

 

 

The Pressure Calibration screen is used to calibrate the pressure sensor to 
zero, span, or factory default values.

 

Use the 

 and 

 buttons to move up and down and the 

 and 

 

buttons to move left and right. 

Home Screen>Settings>Measurement Settings>Advanced Measurement 
Settings>Pressure Calibration

 

 

The Pressure Calibration screen contains the following information: 

●

 

Across: 

●

 

Description:

 Lists items in table. 

●

 

Reading:

 Displays reading of each pressure sensor. 

●

 

Calibration:

 Starts calibration or resets default values. 

●

 

Down: 

●

 

Sensor 1

3 Reading:

 Under the column labeled Reading, current 

reading of each pressure sensor. 

●

 

Atmospheric Sensor 1

3:

 Under the column labeled reading, the user 

enters the current atmospheric pressure in mmHg units. Under the 
column labelled Calibration, the user presses the Start button to 
calibrate the high point of the sensor. 

●

 

Zero Sensor 1

3:

 User should put the pressure sensor under a strong 

vacuum. Under the column labeled reading, the user enters the 
pressure in mmHg. Under the column labeled Calibration, the user 
presses the Start button to calibrate the low point of the sensor. 

●

 

Reset all values:

 Resets values to default. 

 

Pressure Calibration

Содержание 42iQTL























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды