Terex Genie Z-62/40 Скачать руководство пользователя страница 69

Страница: 69 / 79

Second Edition • First Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 1304187GT

-62/40 • Z

-62/40 TRAX

™

Securing to Truck or Trailer for
Transit

Always use the turntable rotation lock pin each time
the machine is transported.

Turntable rotation lock pin

Turn the key switch to the off position and remove
the key before transporting.

Inspect the entire machine for loose or unsecured
items.

Securing the Chassis

Use chains of ample load capacity.

Use a minimum of 6 chains.

Adjust the rigging to prevent damage to the chains.

For diagram, refer to the Lifting Instructions.

Securing the Platform

Make sure the jib and platform are in the stowed
position.

Secure the platform with a nylon strap placed
through the lower platform support. Do not use
excessive downward force when securing the
boom section.

Содержание Genie Z-62/40
















































































Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды

Terex Genie Z-62/40, Руководство оператора

Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды