Terex Genie Z-62/40 Скачать руководство пользователя страница 45

Страница: 45 / 79

Second Edition • First Printing

Operator's Manual

Inspections

Part No. 1304187GT

-62/40 • Z

-62/40 TRAX

™

Test Limited Drive Speed

Press down the foot switch.

Raise the primary boom approximately 2 ft /
61 cm.

Slowly move the drive control handle to the full
drive position.

Result: The maximum achievable drive speed
with the primary boom raised should not
exceed 1 ft / 30 cm per second.

Lower the primary boom to the stowed
position.

Extend the primary boom approximately
2 feet/61 cm.

Slowly move the drive control handle to the full
drive position.

Result: The maximum achievable drive speed
with the primary boom extended should not
exceed 1 ft/30 cm per second.

Retract the primary boom to the stowed
position.

Raise the secondary boom approximately
2 feet/61 cm.

Slowly move the drive control handle to the full
drive position.

Result: The maximum achievable drive speed
with the secondary boom raised should not
exceed 1 ft / 30 cm per second.

Lower the secondary boom to the stowed
position.

If the drive speed with the primary or secondary
boom raised or the primary boom extended
exceeds 1 ft/30 cm per second, immediately tag
and remove the machine from service.

Test Drive Tilt Cutout

Press down the foot switch.

With the boom fully stowed, drive the machine
onto a slope where the chassis pitch angle is
greater than 4.5°.

Result: The machine should continue to drive.

Return to level ground and raise the primary
boom to an out of stowed position
(approximately 10° above horizontal).

Drive the machine onto a slope where the
chassis pitch angle is greater than 4.5°.

Result: The machine should stop once the
machine reaches 4.5° of chassis tilt and the
alarm should sound at the platform controls.

Lower the primary boom to the stowed
position.

Result: The alarm should turn off and the
machine should drive.

Return to level ground and extend the primary
boom approximately 1.6 ft / 0.5 m.

Drive the machine onto a slope where the
chassis pitch angle is greater than 4.5°.

Result: The machine should stop once the
machine reaches 4.5° of chassis tilt and the
alarm should sound at the platform controls.

Retract the primary boom to the stowed
position.

Result: The alarm should turn off and the
machine should drive.

Содержание Genie Z-62/40
















































































Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды

Terex Genie Z-62/40, Руководство оператора

Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды