Terex Genie Z-62/40 Скачать руководство пользователя страница 58

Страница: 58 / 79

Operator's Manual

Second Edition • First Printing

Operating Instructions

56 Z

-62/40 • Z

-62/40 TRAX

™

Part No. 1304187GT

Tilt Sensor Activation Settings

Model

Chassis Angle

(side to side)

Chassis Angle

(front to back)

Z-62/40
Z-62/40 TraX

4.5° 4.5°

When the Machine On Incline
indicator light is on and the tilt
alarm sounds, the following
functions are affected; drive
functions are disabled.

To restore drive functions,
follow the steps to lower the
boom in the Machine Not
Level Indicator Light
procedure.

When the machine is stowed,
on a slope, and the tilt alarm
sounds, the following
functions are affected; lift
functions are disabled.

Return the machine to level
ground to restore lift functions.

Engine Idle Select (rpm)

When the foot switch is not pressed, the engine will
idle at the lowest rpm.

•

Turtle symbol: Foot
switch activated low idle

•

Rabbit symbol: Foot
switch activated high idle

If foot switch activated low idle or high idle do not
work, contact service personnel within 24 hours.

Foot switch activated idle settings are disabled by
certain fault codes.

Generator (if equipped)

To start the generator, move
the generator toggle switch to
the on position.

Plug a power tool into the
power to platform GFCI outlet.

To turn off the generator, move the generator
toggle switch to the off position.

Note: Machine functions will not operate while the
generator is running and the foot switch is not
pressed down. When the foot switch is pressed
down, the generator will turn off and the machine
functions will operate.

Содержание Genie Z-62/40
















































































Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды

Terex Genie Z-62/40, Руководство оператора

Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды