Terex Genie Z-62/40 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 79

background image

Second Edition • First Printing

Operator's Manual

Controls

Part No. 1304187GT

Z

®

-62/40 • Z

®

-62/40 TRAX

™

25

9

Red Emergency Stop button

Push in the red Emergency Stop button to the
off position to stop all functions and turn the
engine off. Pull out the red Emergency Stop
button to the on position to operate the
machine.

10

Jib boom up/down switch

Move the jib boom switch up and the jib boom
will raise. Move the jib boom switch down and
the jib boom will lower.

11

Gasoline/LPG models: Fuel select switch

Move the fuel select switch to the gasoline
position to select gasoline. Move the fuel select
switch to the LPG position to select LPG.

12

Platform level switch

Move the platform level switch up and the level
of the platform will raise. Move the platform
level switch down and the level of the platform
will lower.

13

Engine idle (rpm) select switch

Move the engine idle select switch to the turtle
position for low idle.
Move the engine idle select switch to the rabbit
position for high idle.

14

Diesel models: Glow plug switch (if equipped)

Move the glow plug switch to either side and
hold for 3 to 5 seconds.

15

Engine start switch

Move the engine start switch to either side to
start the engine.

16

Platform rotate switch

Move the platform rotate switch to the right and
the platform will rotate to the right. Move the
platform rotate switch to the left and the
platform will rotate to the left.

17

Auxiliary power switch

Use auxiliary power if the primary power
source (engine) fails.
Simultaneously hold the auxiliary power switch
to either side and activate the desired function.

18

Turntable rotate switch

Move the turntable rotate switch to the right
and the turntable will rotate to the right. Move
the turntable rotate switch to the left and the
turntable will rotate to the left.

19

Regeneration Enable switch (models with LCD
screen)

Move the Regeneration Enable switch to the
right to enable all the machine functions. Move
the Regeneration Enable switch to the left to
disable all the machine functions.

«
...
25
26
27
28
29
...
»

Содержание Genie Z-62/40
















































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Z-62/40

Бренд: ELS LIFT Страницы: 57

Euroline JA3000S-E

Бренд: Jema Autolifte Страницы: 20

Бренд: Terex Страницы: 341

Genie GTH-4020 ER

Бренд: Terex Страницы: 188

Бренд: Ravaglioli Страницы: 74

Бренд: Wesco Страницы: 5

Бренд: Wesco Страницы: 7

Бренд: TLS Страницы: 30

Бренд: TLS Страницы: 30

Бренд: JLG Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды