Terex Genie Z-62/40 Скачать руководство пользователя страница 67

Страница: 67 / 79

Second Edition • First Printing

Operator's Manual

Towing

Instructions

Part No. 1304187GT

-62/40 • Z

-62/40 TRAX

™

Towing Instructions

Using the Tow Package

Before Towing:

Position the machine on a level surface. Chock
the wheels to prevent the machine from rolling.

Attach the tow bar securely to the machine.
Attach the tow bar securely to the towing
vehicle.

Release the drive torque hubs by turning over
the drive hub disconnect caps.

4WD models: Release the front drive torque
hubs by turning over the drive disconnect caps.

Turn the steering bypass valve
counterclockwise to hydraulically release the
steering.

Do not exceed recommended
maximum towing speed or
maximum towing times.

Maximum tow speed

8 mph/13 km/h

Maximum towing time at
8 mph/13 km/h

30 minutes

Maximum towing time at
6 mph/10 km/h

60 minutes

After Towing:

Immediately after towing, chock the wheels,
detach the tow bar and reverse the drive hub
disconnect caps.

Secure the tow bar back onto the machine.

Test steer, drive and brake functions on a level
surface prior to returning the machine to
operation. See Function Tests.

WARNING

Содержание Genie Z-62/40
















































































Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды

Terex Genie Z-62/40, Руководство оператора

Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды