Terex Genie Z-62/40 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 79

background image

Operator's Manual

Second Edition • First Printing

Controls

34 Z

®

-62/40 • Z

®

-62/40 TRAX

™

Part No. 1304187GT

Platform Control Panel, Models
With LCD Screen

1

Horn button

Press this button and the horn will sound.
Release the button and the horn will stop.

2

Platform level switch

Move the platform level
switch up and the level of the
platform will raise. Move the
platform level switch down
and the level of the platform
will lower.

3

Platform rotate switch

Move the platform rotate
switch to the right and the
platform will rotate to the
right. Move the platform
rotate switch to the left and
the platform will rotate to
the left.

4

Jib boom up/down switch

Move the jib boom switch
up and the jib boom will
raise. Move the jib boom
switch down and the jib
boom will lower.

5

Platform overload indicator light

Light flashing indicates the platform is
overloaded. The engine will stop and no
functions will operate. Remove weight until the
light goes off and then restart the engine.

6

Machine not level indicator light

Light on indicates the tilt sensor activation
settings have been exceeded. See the
instructions in the Operating Instructions
section.

7

Auxiliary power switch

Use auxiliary power if the primary power
source (engine) fails.
Simultaneously hold the auxiliary power switch
to either side and activate the desired function.

8

Drive speed select switch

Machine on incline symbol: Low range
operation for inclines.
Machine on level surface symbol: High range
operation for maximum drive speed.

9

Platform control box heater (if equipped)

Move the heater switch up to turn on the
platform control box heater. Move the heater
switch down to turn off the platform control box
heater.

10

Generator switch (if equipped)

Move the generator switch up to activate the
generator. Move the switch down to turn off the
generator.

«
...
34
35
36
37
38
...
»

Содержание Genie Z-62/40
















































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Z-62/40

Бренд: Genie Страницы: 56

Бренд: Genie Страницы: 59

Бренд: S.D.P. Страницы: 78

Бренд: DINGLI Страницы: 66

Бренд: Terex Страницы: 60

Бренд: Skyjack Страницы: 88

SJ6832 RTE Series

Бренд: Skyjack Страницы: 112

Бренд: Skyjack Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды