Terex Genie Z-62/40 Скачать руководство пользователя страница 20

Страница: 20 / 79

Operator's Manual

Second Edition • First Printing

Work Area Safety

18 Z

-62/40 • Z

-62/40 TRAX

™

Part No. 1304187GT

Damaged Machine Hazards

Do not use a damaged or malfunctioning machine.

Conduct a thorough pre-operation inspection of the
machine and test all functions before each work
shift. Immediately tag and remove from service a
damaged or malfunctioning machine.

Be sure all maintenance has been performed as
specified in this manual and the appropriate Genie
service manual.

Be sure all decals are in place and legible.

Be sure the operator's, safety, and responsibilities
manuals are complete, legible, and in the storage
container located on the machine.

Component Damage Hazards

Do not use any battery or charger greater than 12V
to jump-start the engine.

Do not use the machine as a ground for welding.

Do not operate the machine in locations where
extremely high magnetic fields may be present.

Battery Safety

Burn Hazards

Batteries contain acid.
Always wear protective
clothing and eye wear when
working with batteries.

Avoid spilling or contacting
battery acid. Neutralize
battery acid spills with baking
soda and water.

Explosion Hazards

Keep sparks, flames, and
lighted tobacco away from
batteries. Batteries emit
explosive gas.

Electrocution Hazard

Avoid contact with electrical terminals.

Содержание Genie Z-62/40
















































































Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды

Terex Genie Z-62/40, Руководство оператора

Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды