Terex Genie Z-62/40 Скачать руководство пользователя страница 48

Страница: 48 / 79

Operator's Manual

Second Edition • First Printing

Inspections

46 Z

-62/40 • Z

-62/40 TRAX

™

Part No. 1304187GT

Operate each machine function.

Result: All machine functions should not
operate.

Insert the actuator into the switch socket.

Result: The lights and horn will turn off.

Operate each machine function.

Result: All machine functions should operate.

actuator

contact alarm cable

flashing alarm

switch socket

Test the Lift/Drive Select Function (if
equipped)

Press down the foot switch.

Move the drive control handle off center and
activate a boom function toggle switch.

Result: No boom functions should operate. The
machine will move in the direction indicated on
the control panel.

Repair any malfunctions before operating the
machine.

Test Aircraft Protection Package
(if equipped)

Note: Two people may be required to perform this
test.

Extend the primary boom approximately
1 ft/30 cm.

Move the yellow bumper at the bottom of the
platform 4 inches/10 cm in any direction.

Activate each function control handle or toggle
switch.

Result: No boom and steer functions should
operate.

Move and hold the aircraft
protection override switch.

Activate each function control handle or toggle
switch.

Result: All boom and steer functions should
operate.

Содержание Genie Z-62/40
















































































Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды

Terex Genie Z-62/40, Руководство оператора

Результаты поиска

Содержание Genie Z-62/40

Отзывы:

Похожие инструкции для Genie Z-62/40

Бренды по названию

Популярные бренды