Terex Genie Z-62/40 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 79

background image

Second Edition • First Printing

Operator's Manual

Inspections

Part No. 1304187GT

Z

®

-62/40 • Z

®

-62/40 TRAX

™

39

Do Not Operate Unless:



You learn and practice the principles of safe
machine operation contained in this operator’s
manual.

1 Avoid

hazardous

situations.

2 Always perform a pre-operation inspection.

3 Always perform function tests prior to

use.

Know and understand the function tests
before going on to the next section.

4 Inspect the workplace.

5 Only use the machine as it was intended.

Function Test Fundamentals

The function tests are designed to discover any
malfunctions before the machine is put into service.
The operator must follow the step-by-step
instructions to test all machine functions.

A malfunctioning machine must never be used. If
malfunctions are discovered, the machine must be
tagged and removed from service. Repairs to the
machine may only be made by a qualified service
technician, according to the manufacturer’s
specifications.

After repairs are completed, the operator must
perform a pre-operation inspection and function
tests again before putting the machine into service.

«
...
39
40
41
42
43
...
»

Содержание Genie Z-62/40
















































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Z-62/40

Бренд: DINGLI Страницы: 66

Бренд: Terex Страницы: 59

Бренд: DINGLI Страницы: 74

Бренд: Total Automotive Lifting Solutions Inc. Страницы: 31

Бренд: Skyjack Страницы: 16

Бренд: Skyjack Страницы: 106

Бренд: Skyjack Страницы: 73

Бренд: Skyjack Страницы: 98

Бренд: Skyjack Страницы: 103

Бренд: Skyjack Страницы: 108

Бренд: Skyjack Страницы: 120

Бренд: Skyjack Страницы: 206

SJIII Compact 3215

Бренд: Skyjack Страницы: 207

Бренд: Skyjack Страницы: 232

Бренд: Skyjack Страницы: 255

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды