Terex Genie SX-105 XC Скачать руководство пользователя страница 66

Страница: 66 / 76

Operator's Manual

First Edition • Third Printing

Transport and Lifting Instructions

™

-105 XC

™

• SX

™

-125 XC

™

Part No. 1270327GT

Observe and Obey:



Only qualified riggers should rig the machine.



Only certified crane operators should lift the
machine and only in accordance with the
applicable crane regulations.



Be sure the crane capacity, loading surfaces
and straps or lines are sufficient to withstand
the machine weight. See the serial label for
the machine weight.

Lifting Instructions (option 1)

Fully extend the axles. Fully lower and retract the
boom. Fully lower the jib.

Remove all loose items on the machine.

Determine the center of gravity of your machine
using the table and the picture on this page.

Attach the rigging only to the designated lifting
points on the machine.

There are four lifting points on the drive chassis,
one lifting point on each axle, and two lifting points
on the riser plate of the swing chassis.

Adjust the rigging to prevent damage to the
machine and to keep the machine level.

Center of gravity

X Axis

Y Axis

SX-105 XC

116 in

2.9 m

58 in

1.5 m

SX-125 XC

131 in

3.3 m

62 in

1.6 m

Содержание Genie SX-105 XC













































































Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Terex Genie SX-105 XC, Руководство оператора, Страница: 66 / 76

Результаты поиска

Содержание Genie SX-105 XC

Отзывы: