Terex Genie SX-105 XC Скачать руководство пользователя страница 52

Страница: 52 / 76

Operator's Manual

First Edition • Third Printing

Operating Instructions

™

-105 XC

™

• SX

™

-125 XC

™

Part No. 1270327GT

Drive Enable

Light on indicates that the boom
has moved past a circle-end tire
and the drive function has been
interrupted.

To drive, move the drive enable switch and slowly
move the drive/steer control handle off center.

If the drive/steer control handle is not moved within
two seconds of moving the drive enable switch,
the drive function will not operate. Release and
move the drive enable switch again.

Be aware that the machine may move in the
opposite direction that the drive and steer controls
are moved.

Always use the color-coded direction arrows on
the platform controls and the drive chassis to
identify the direction the machine will travel.

When the drive enable light is on, the axles cannot
retract.

Engine Idle Select (rpm)

Select the engine idle (rpm) by
pressing the engine idle select
switch. The indicator light next to
the current setting will be on.



Turtle symbol: low idle



Rabbit symbol: high idle

Check Engine Light

Light on and engine stopped: Tag the
machine and remove from service.

Light on and engine still running:
Contact service personnel within
24 hours.

Содержание Genie SX-105 XC













































































Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды

Terex Genie SX-105 XC, Руководство оператора

Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды