Terex Genie SX-105 XC Скачать руководство пользователя страница 37

Страница: 37 / 76

First Edition • Third Printing

Operator's Manual

Inspections

Part No. 1270327GT

™

-105 XC

™

• SX

™

-125 XC

™

Test the Tilt Sensor

Press one of the LCD
screen control buttons until
TURNTABLE LEVEL
SENSOR X-DIRECTION
appears.

Result: The LCD screen should display the
angle in degrees.

Press the LCD screen control buttons until
TURNTABLE LEVEL SENSOR Y-DIRECTION
appears.

Result: The LCD screen should display the
angle in degrees.

Press the LCD screen control buttons until
PLATFORM LEVEL SENSOR DEGREES
appears.

Result: The LCD screen should display the
angle in degrees.

Test the Operating Envelope

Simultaneously press the 2
LCD screen control buttons
shown to activate status
mode.

Press one of the LCD
screen control buttons
shown until PRIMARY
ANGLE DEGREES is
displayed.

Raise the boom and observe the LCD screen.

Result: The LCD screen will display the boom
angle to gravity in degrees.

Press one of the LCD
screen control buttons
shown until LENGTH
SENSOR EXTENSION
INCHES is displayed.

Extend the boom and observe the LCD
screen.

Result: The LCD screen will display the string
pot extension length.

Retract the boom.

Содержание Genie SX-105 XC













































































Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Terex Genie SX-105 XC, Руководство оператора, Страница: 37 / 76

Результаты поиска

Содержание Genie SX-105 XC

Отзывы: