Terex Genie SX-105 XC Скачать руководство пользователя страница 57

Страница: 57 / 76

First Edition • Third Printing

Operator's Manual

Operating Instructions

Part No. 1270327GT

™

-105 XC

™

• SX

™

-125 XC

™

The LCD screen displays the message
NOTICE: ALL FUNCTIONS WILL BE
LOCKED. REGEN WILL TAKE APPROX. 1
HOUR. PRESS ENTER.

Press the LCD screen control button
shown.

If the engine is not already running, the LCD
screen displays the message START THE
ENGINE THEN PRESS ENTER.

Start the engine, if not already done
and press the LCD screen control
button shown.

The LCD screen displays the message
REGEN REQUESTED. At this time, the
system will warm the engine, if necessary, and
proceed with the process.

If the Regeneration process has begun
successfully, the LCD screen displays the
message REGEN TIME REMAINING.

Once the regeneration is completed, the LCD
screen displays the message REGEN
SUCCESSFUL.

If the LCD screen displays the message
REGEN CANCELLED, then something is
preventing the Regeneration process from
completing. Contact Genie service for
assistance.

Содержание Genie SX-105 XC













































































Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды

Terex Genie SX-105 XC, Руководство оператора

Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды