Terex Genie SX-105 XC Скачать руководство пользователя страница 63

Страница: 63 / 76

First Edition • Third Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 1270327GT

™

-105 XC

™

• SX

™

-125 XC

™

Securing to Truck or Trailer for
Transit

Always use the turntable rotation lock pin each
time the machine is transported.

Turntable rotation lock pin

Turn the key switch to the off position and remove
the key before transporting.

Inspect the entire machine for loose or unsecured
items.

Securing the Platform

Lower the jib boom to the stowed position.

Lower the platform as far as it will go, so that the
jib and platform are tucked underneath the boom.

Run a strap through the platform support between
the plates next to the rotator.

Anchor the strap to each corner of the truck bed.

The platform will hang over the end of the truck.

Содержание Genie SX-105 XC













































































Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды

Terex Genie SX-105 XC, Руководство оператора

Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды