Terex Genie SX-105 XC Скачать руководство пользователя страница 30

Страница: 30 / 76

Operator's Manual

First Edition • Third Printing

Controls

™

-105 XC

™

• SX

™

-125 XC

™

Part No. 1270327GT

Steer mode select switch with indicator lights

Move the steer
mode select switch
to choose steer
mode.
The indicator light
next to the current
steer mode will be
on.

Dual axis proportional control handle for jib
boom up/down and platform rotate left/right
functions

Move the control handle
up and the jib boom will
raise. Move the control
handle down and the jib
boom will lower.

Move the control handle
to the left and the
platform will rotate to the
left. Move the control
handle to the right and
the platform will rotate to
the right.

Drive select switch with indicator lights

Move the drive select
switch to choose drive
setting. The indicator
light next to the current
setting will be on.

Machine on incline
symbol: Low range
operation for inclines.

Machine on level
surface symbol: High
range operation for
maximum drive speed.

Single axis proportional control handle for
boom extend/retract function

Move the control handle
down and the boom will
extend. Move the control
handle up and the boom will
retract.

Содержание Genie SX-105 XC













































































Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды

Terex Genie SX-105 XC, Руководство оператора

Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды