Terex Genie SX-105 XC Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 76

Terex Genie SX-105 XC Скачать руководство пользователя страница 34

Operator's Manual

First Edition • Third Printing

Inspections

32

SX

™

-105 XC

™

• SX

™

-125 XC

™

Part No. 1270327GT

Do Not Operate Unless:



You learn and practice the principles of safe
machine operation contained in this operator’s
manual.

1 Avoid hazardous situations.

2 Always perform a pre-operation inspection.

3 Always perform function tests prior to

use.

Know and understand the function tests
before going on to the next section.

4 Inspect the workplace.

5 Only use the machine as it was intended.

Function Test Fundamentals

The function tests are designed to discover any
malfunctions before the machine is put into
service. The operator must follow the step-by-step
instructions to test all machine functions.

A malfunctioning machine must never be used. If
malfunctions are discovered, the machine must be
tagged and removed from service. Repairs to the
machine may only be made by a qualified service
technician, according to the manufacturer’s
specifications.

After repairs are completed, the operator must
perform a pre-operation inspection and function
tests again before putting the machine into
service.

«
...
32
33
34
35
36
...
»

Содержание Genie SX-105 XC













































































Отзывы:

Нет отзывов