Terex Genie SX-105 XC Скачать руководство пользователя страница 17

Страница: 17 / 76

First Edition • Third Printing

Operator's Manual

Work Area Safety

Part No. 1270327GT

™

-105 XC

™

• SX

™

-125 XC

™

Fall Hazards

Occupants must wear a
safety belt or harness in
accordance with
governmental regulations.
Attach the lanyard to the
anchor provided in the
platform.

Do not sit, stand, or climb
on the platform guard rails.
Maintain a firm footing on
the platform floor at all
times.

Do not climb down from the
platform when raised.

Keep the platform floor clear of debris.

Lower the platform entry mid-rail or close the entry
gate before operating.

Do not enter or exit the platform unless the
machine is in the stowed position and the platform
is at ground level.

Hazards related with the specific product
application of exiting at height have been
considered in the design of the machine, for
further information contact Genie (see section
Contacting the Manufacturer).

Collision Hazards

Be aware of limited sight
distance and blind spots
when driving or operating.

Be aware of the boom position and tailswing when
rotating the turntable.

Check the work area for
overhead obstructions or
other possible hazards.

Be aware of crushing
hazards when grasping
the platform guard rail.

Operators must comply with employer, job site,
and governmental rules regarding use of personal
protective equipment.

Содержание Genie SX-105 XC













































































Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды

Terex Genie SX-105 XC, Руководство оператора

Результаты поиска

Содержание Genie SX-105 XC

Отзывы:

Похожие инструкции для Genie SX-105 XC

Бренды по названию

Популярные бренды