50
EN
E
N
4
.
M
ai
n
te
n
an
ce
a
n
d
c
le
an
in
g
37878
05-2017
4.6
Trouble shooting
Alarm message 109 to 123
ã
Terberg Machines B.V., IJsselstein, The Netherlands
All rights reserved. No part of this book may be reproduced, stored in database or retrieval system, or published, in any form or in any way,
electronically, mechanically, by print, photoprint, microfilm or any other means without prior written permission from the publisher.
109: R/H HS2 (CHAIR)
ERRATIC READING
A position sensor difference error caused by
position sensor HS2 on the R/H side.
Linearity check.
This is a timer based interval check, with the bin lift
in motion it checks the old position value and the
current position value. If the difference in position
is too big, this event is remembered in a counter.
When the value of this counter reaches a selected
maximum nr. of errors (5), this message is display-
ed.
Check for axial and radial play where HS2 is
located.
Check the position sensor HS2.
Check the sensor signal on analogue input 00.3
Check the actuating levers connected to the
sensor.
Check cables and connectors to HS2.
110: RH HS1 (TILT)
OUT OF RANGE
The position sensor HS1 on the R/H side is out of
range.
The analogue input 00.2 value must be between
100 and 900 steps. Any step over or under this
value is not a normal situation.
Check for axial and radial play where HS1 is
located.
Check the magnet from position sensor HS1.
Check the position sensor HS1.
Check the sensor signal on analogue input 00.2
Check cables and connectors to HS1.
111: RH HS2 (CHAIR)
OUT OF RANGE
The position sensor HS2 on the R/H side is out of
range.
The analogue input 00.3 value must be between
100 and 900 steps. Any step over or under this
value is not a normal situation.
Check for axial and radial play where HS2 is
located.
Check the actuating levers connected to the
sensor.
Check the position sensor HS2.
Check the sensor signal on analogue input 00.3
Check cables and connectors to HS2.
112: PRESSURE TOO HIGH
L/H
Oil pressure too high for the L/H chair, lifting
2-wheel (domestic) bins.
The bin lift will stop.
The bin applied to the bin lift is too heavy.
An object or debris is blocking the bin lifts
movement.
113: PRESSURE TOO HIGH
R/H
Oil pressure too high for the R/H chair, lifting
2-wheel (domestic) bins.
The bin lift will stop.
114: PRESSURE TOO HIGH
TRADE CONTAINER
Oil pressure too high for lifting a 4-wheel (trade)
container.
The bin lift will stop.
The container applied to the bin lift is too heavy.
An object or debris is blocking the bin lifts
movement.
115: BIN TOO HEAVY
L/H
For bin lifts with dynamic weighing by pressure.
The maximum allowed bin weight is reached, the
bin lift will be stopped.
The bin applied to the bin lift is too heavy.
An object or debris is blocking the bin lifts
movement.
116: BIN TOO HEAVY
R/H
117: TRADE CONTAINER
TOO HEAVY
For bin lifts with dynamic weighing by pressure.
The maximum allowed container weight is reached,
the bin lift will be stopped.
The container applied to the bin lift is too heavy.
An object or debris is blocking the bin lifts
movement.
118: L/H SWITCH TO 2W
MOVE LIFTER TO TOP
OmniDEKA bin lift:
Tilting sensor (HS1) of the L/H chair is out of range
of the safe position and needs to be corrected.
In this case an up and down movement in
2-wheel domestic mode, without a bin on the
comb, will correct the tilting.
119: R/H SWITCH TO 2W
MOVE LIFTER TO TOP
OmniDEKA bin lift:
Tilting sensor (HS1) of the R/H chair is out of range
of the safe position and needs to be corrected.
120: L/H HS1 (TILT)
CHECK POS OF MAGNET
OmniDEKA bin lift:
Position of the L/H HS1 position sensor.
The HS1 and HS2 position sensors are sensors
which are using a magnet to detect the position.
This message appears if the magnetic field is not
detected correctly. For example there are black
spots because the magnet is too far away from
the HALL sensor.
121: L/H HS2 (CHAIR)
CHECK POS OF MAGNET
OmniDEKA bin lift:
Position of the L/H HS2 position sensor.
122: R/H HS1 (TILT)
CHECK POS OF MAGNET
OmniDEKA bin lift:
Position of the R/H HS1 position sensor.
123: R/H HS2 (CHAIR)
CHECK POS OF MAGNET
OmniDEKA bin lift:
Position of the R/H HS2 position sensor.
