46
EN
E
N
4
.
M
ai
n
te
n
an
ce
a
n
d
c
le
an
in
g
37878
05-2017
4.6
Trouble shooting
Alarm message 59 to 68
ã
Terberg Machines B.V., IJsselstein, The Netherlands
All rights reserved. No part of this book may be reproduced, stored in database or retrieval system, or published, in any form or in any way,
electronically, mechanically, by print, photoprint, microfilm or any other means without prior written permission from the publisher.
59: MOTOR CONTROLLER
RH
For electric bin lifts with CAN to CAN interface
only. An error has been received from the R/H
electric motor controller.
There is something wrong with the R/H motor
controller or R/H electric motor. Please contact
your local Terberg dealer.
60: CAN BUS ERROR
General bin lift CAN bus error.
A CAN bus error can be caused by the following
failures:
1. Termination of CAN bus not OK
2. A defect CAN cable.
3. One or more CAN devices are broken or
cannot be found by the controller.
4. Wrong bit rate or CAN settings
(at installation only).
If a specific CAN device is not found by the con-
troller this can be displayed behind the alarm mes-
sage as well.
Check 120Ω line resistance.
Check all CAN related cables
Please contact your local Terberg dealer.
61: DATA STORAGE
FAILURE
Identification or weighing system backup memory
error.
No external storage memory is placed in the iden-
tification system or weighing system.
For weighing system TMDW9004 / TMDW9009 /
TMDW8010 only.
Check if a data card is loaded into the on-board
data card reader.
Make sure the data card has been setup correct-
ly and format is correct.
Check if the data card reader power supply is OK.
62: WASHING BUSY
L/H
Bin lifts with washing systems only.
L/H lifter is in the tipped position and washing is
busy.
Washing system is sending a signal to the bin lift
that it must wait in the tipped position until the
washing is fully done.
Wait until the bin washing cycle is completed.
63: WASHING BUSY
R/H
Bin lifts with washing systems only.
R/H lifter is in the tipped position and washing is
busy.
Washing system is sending a signal to the bin lift
that it must wait in the tipped position until the
washing is fully done.
64: WASHING SYSTEM
OUT OF POSITION
Washing system asks the bin lift to stop before it
has even reached the tipping position.
Washing heads are not fully retracted in the safe
position.
The bin lift has not even given the washing system
a signal it is in the top position.
Incorrect signals from the bin wash system or the
bin wash system is offline.
65:
Not used.
66: PICKUP ARMS
WITHOUT LOCK
The lock option is set and DIN-arms are not open
/ unfolded and 4-wheel / trade unlock sensor is set.
Lock both chairs together when emptying
containers with DIN-arms.
67: POSITION OR
OUTPUT FAILURE
One of the lifting chairs has moved up or down
more than 10% without the opening of valves or by
any command from the controller.
The L/H chair has moved without output
command.
The R/H chair has moved without output
command.
Speed error detected above half height position.
The bin lift could have been pushed up by ground
collision.
The locking pin is (partially) engaged in 2-wheel
mode, making one chair lifting up the other chair.
If no logic reason is found like the two mentioned
above, please check the position sensors and/or
outputs and valves.
68: RCV NOT READY
The compactor / RCV is not producing a “ready to
work” signal on the 16-pin plug connections.
The bin lift is not allowed to move or ask for
hydraulic power from the refuse compactor.
Find out why the bin lift does not receive an “RCV
ready” signal from the refuse body.
Make sure the refuse body controller is OK.
Make sure the gearbox is in Neutral.
Make sure the PTO is active.
