EN
51
E
N
37878
05-2017
4
.
M
ai
n
te
n
an
ce
a
n
d
c
le
an
in
g
4.6
Trouble shooting
Alarm message 124 to 137
ã
Terberg Machines B.V., IJsselstein, The Netherlands
All rights reserved. No part of this book may be reproduced, stored in database or retrieval system, or published, in any form or in any way,
electronically, mechanically, by print, photoprint, microfilm or any other means without prior written permission from the publisher.
124: CLEANOPEN COMM
IDENT IS NOT READY
For bin lifts with an external identification system
connected to the bin lifts Clean Open CAN con-
nection port and the bin lift has been setup to stop
when this third party identification system is not
ready (offline). The bin lift stops to prevent illegal
emptying of bins without identification.
Make sure this identification system is online and
ready to communicate.
125: CLEANOPEN STOP
COMMUNICATION ERROR
Third party identification system connected to
CleANopen CAN Bus.
For bin lifts with an external identification system
connected to the bin lifts Clean Open CAN con-
nection port and the bin lift has been setup to stop
when this third party identification system is not
ready (offline), or CAN bus connection fails. The
bin lift stops to prevent illegal emptying of bins
without identification.
126: L/H SPEED ERROR
CORRECTION ACTIVE
L/H chair, bin lift speed has been detected as being
too high.
The bin lift speed is corrected to a lower speed to
prevent damage and dangerous situations.
If this occurs during setup, lower the bin lift speed
to the allowed speed to solve this problem.
If this occurs during normal operation, please
check the position sensors and proportional valves.
Else please contact your local Terberg dealer.
127: R/H SPEED ERROR
CORRECTION ACTIVE
R/H chair, bin lift speed has been detected as being
too high.
The bin lift speed is corrected to a lower speed to
prevent damage and dangerous situations.
128: SMT STOP HIGHER
THEN WEIGHING START
Stop position of single man trade (SMT) stop is
inside the pressure weighing window, which result
in a failure in calculating the bin weight.
This message is displayed for correction of the
weighing start position to a higher position as the
stop SMT position.
129: FOOTBOARD BLOCK
CATCHERBAR BUTTON
Footboard is occupied and the catcherbar button is
pressed.
In this case the catcherbar does not change the
position and this message is displayed to inform the
user why it is not changing the position.
130: L/H N6 ERROR
BIN NOT DETECTED
Message is displayed if the bin lift is in 2-wheel auto-
matic mode, after lifting chair moves up and the bin
on comb sensor N6 lost contact with bin or is not
detecting a bin on the detection position.
131: R/H N6 ERROR
BIN NOT DETECTED
132: L/H N11 SENSOR
4 WHEEL BIN ERROR
Message is displayed when (N11) 4-wheel contai-
ner detection sensor input stays active.
Message will be reset as soon input is deactivated.
133: R/H N11 SENSOR
4 WHEEL BIN ERROR
134: L/H N6 SENSOR
COMB NOT REACHED
Message is displayed if the bin lift is in 2-wheel auto-
matic mode, after lifting chair moves up and the bin
on comb sensor N6 has no contact within 40cm
the chair starts to move up.
Bin lift stops to move up and message is reset
by manual move up or down.
135: R/H N6 SENSOR
COMB NOT REACHED
136: TRD N6 SENSORS
COMB NOT REACHED
Message is displayed if the bin lift is in 4-wheel sing-
le man trade (SMT) mode, after the chairs move
up and the container on comb sensor N6 has no
contact within 40cm the chairs start to move up.
137: GOTO POSITION
NOT IN RANGE STOP
Message is displayed if the bin lift has to go to a
fixed position and the position is out of range of
the 40cm from the current position.
Bin lift will move to the position which is inside the
40cm and message will be displayed as sign the
position to go to is outside the 40cm range.
