Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 196

background image

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

80

2019-08-05

Synchronous Response

Table 50, page 81

describes the synchronous responses and remarks for the Mode

command.

inactivity time-out in
LAP mode

Optional

Minimum value: 1
Maximum value:
65535
Default value: 360
Unit: seconds

This value specifies the inactivity time out
per STA, after which LAP send a
NULL/QoS-NULL frame expecting the
STA to MAC level acknowledge it.
When there is no activity from a connected
node, the module waits for 360 seconds and
sends a probe to the inactive node. If there
is no response, then it disconnects itself
from the inactive node.GS2000 does not
send disassociation frame to STA.

Note:

GS2000 doesn't send dis-association

frame to STA.

reserved

Optional

NA

NA

rate
adaptation-device
type

Optional

0,1
0: Battery powered
/Ultra low power
profile
1: Line
powered/Throughput
profile
0(default)

It helps the WLAN subsystem in fine
tuning the chosen rate adaptation.
The rate adaptation algorithm depends on
the following application profiles:

Ultra low power profile:

This profile

concentrates on saving power as it uses
battery powered devices and they have
strict battery life.

Throughput profile:

This profile has a

requirement of minimum throughput as it
uses line powered or battery powered
devices without a stringent battery life.

Note:

rate
adaptation-minimum
application
throughput

Optional

0-22 Mbps
Default value: 0

This is used to derive minimum PHY rate in
rate adaptation algorithm.

Note:

If rate adaptation - device type is

chosen as 0, then this parameter should be
set to 0.

Note:

1.) Minimum throughput is very much dependent on TCP/UDP.
2.) Rate adaptation-device type and rate adaptation-minimum application throughput parameter is to be provided,
since both go in pair
3.) These parameters are only a guidance to WLAN. The system tries to achieve it but it may not be always
achievable due to various circumstances such as WiFi environments, application use case, and so on.

Table 49 Mode Parameters

Parameter

Optional/Mandatory

Value

Description

«
...
78
79
80
81
82
...
»

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS2101M Series

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: Galcon Страницы: 32

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

ACTIVE DRIVER M/M 1.1

Бренд: DAB Страницы: 10

Бренд: d&b audiotechnik Страницы: 3

ACTIVE DRIVER M/M 1.1

Бренд: DAB PUMPS Страницы: 38

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Parkside Страницы: 65

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Ziton Страницы: 36

Бренд: hager Страницы: 4

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

Бренд: TUYA Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды