Главная
/
Telit Wireless Solutions
/
GS2101M Series
/
Справочник по командам

Telit Wireless Solutions GS2101M Series, Справочник по командам

Поделиться

Страница: 134 / 196

background image

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

134

2019-08-05

5.4.8 Client Join

This command is used to join the P2P group owner. Provision discovery request and
response (AT+P2PPD) needs to be exchanged with the group owner’s intent to join.

Command Syntax

AT+P2PJOIN=<GO MAC address>,<wps config
method>,<WPS-pin><CR>

Parameter Description

Table 112, page 134

describes the Client Join parameters.

Synchronous Response

Table 113, page 135

describes the synchronous responses and remarks for the Client Join

command.

Table 112 Client Join Parameters

Parameter

Optional/mandatory

Value

Description

GO MAC address

Mandatory

N/A

The device MAC address of the group owner
(xx.xx.xx.xx.xx.xx).

WPS Config method Mandatory

N/A

The WPS method to use for WPS procedure

• 0 - WPS-push button
• 1 - WPS-display
• 2 - WPS-keypad

The same configuration method is issued that is
provided in the provision discovery request
(AT+P2PPD)

WPS-Pin

Mandatory

N/A

The pin should be entered in the following cases:

1. If wps_method is keypad, then the entered pin

is passed (displayed by peer).

2. If wps_method is displayed, then the pin

displayed is passed (keypad by peer).

The length allowed is 8 characters.

«
...
132
133
134
135
136
...
»

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS2101M Series

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

Бренд: iluminize Страницы: 2

Бренд: Apex Toys Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды