Главная
/
Telit Wireless Solutions
/
GS2101M Series
/
Справочник по командам

Telit Wireless Solutions GS2101M Series, Справочник по командам

Поделиться

Страница: 145 / 196

background image

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

145

2019-08-05

6.2.2 Battery Warning/Standby Level Set

This command is used to set the battery warning/standby level to and enable the GS node’s
internal battery level monitoring logic starts. This command should be executed before the
battery check start command (see

6.2.1 Battery Check Start, page 144

Command Syntax

AT+BATTLVLSET=<Warning Level>,<Warning
Frequency>,<Standby Level>

Parameter Description

Table 124, page 145

describes the Battery Warning/Standby Level Set parameters.

Synchronous Response

Table 125, page 145

describes the synchronous responses and remarks for Battery

Warning/Standby Level Set command.

Table 124 Battery Warning/Standby Level Set Parameters

Parameter

Optional/Mandatory

Value

Description

Warning Level

Mandatory

N/A

The battery voltage, in millivolts.
When the GS node batter voltage is
less than this level, it sends a message
“Battery Low” to the serial interface.

Warning Frequency

Mandatory

N/A

This is the frequency at which the GS
node sends the “Battery Low”
message to the serial interface once
the GS node’s battery check detected
low battery.

Standby Level

Mandatory

N/A

The battery voltage, in millivolts.
When the GS node battery voltage
reaches this level, it sends the
message “Battery Dead” to the serial
interface and goes into a long Standby
mode.

Table 125 Battery Warning/Standby Level Set Synchronous Responses

Responses

Remarks

OK

Success

ERROR:INVALID INPUT

If parameters are not valid.

«
...
143
144
145
146
147
...
»

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS2101M Series

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: U-Prox Страницы: 31

Бренд: Handicare Страницы: 56

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: Sanhua Страницы: 3

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: Radionics Страницы: 14

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: DSE Страницы: 2

Бренд: GEM Страницы: 17

Бренд: Dantherm Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды