Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 36

Страница: 36 / 196

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

2019-08-05

3.2.1.3 Hardware Flow Control

This command is used to enable or disable hardware flow control for the UART interface.

Command Syntax

AT&Rn

Parameter Description

Table 14, page 36

describes the Hardware Flow Control parameters.

Synchronous Response

Table 15, page 36

describes the synchronous responses and remarks for the Hardware Flow

Control command.

Table 14 Hardware Flow Control Parameters

Parameter

Optional/Mandatory

Value

Description

Mandatory

0 (default)

Hardware flow control is disabled.

Hardware flow control is enabled.

Table 15 Hardware Flow Control Synchronous Responses

Responses

Remarks

Success

ERROR:INVALID INPUT

If parameter is not valid.
(other than 0 or 1)

Содержание GS2101M Series





































































































































































































Результаты поиска

Содержание GS2101M Series

Отзывы:

Telit Wireless Solutions GS2101M Series, Справочник по командам, Страница: 36 / 196

Результаты поиска

Содержание GS2101M Series

Отзывы: