Главная
/
Telit Wireless Solutions
/
GS2101M Series
/
Справочник по командам

Telit Wireless Solutions GS2101M Series, Справочник по командам

Поделиться

Страница: 152 / 196

background image

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

152

2019-08-05

6.3.2.3 Configuring Standby Between Beacons

This command is used to configure GS node to support transitioning to ultra low power
standby mode between beacons.

Command Syntax

AT+PSSTBYBWBEACONCONF = <Conf ID>,<Value>

Parameter Description

Table 134, page 152

describes the Configuring standby mode between beacons parameters.

Table 134 Configure Standby Mode Between Beacons Parameters

Parameter

Optional/Mandatory

Conf ID

Value

Description

Conf ID, Value

Mandatory

0

Alarm 1 wakeup

Value range:

0, 1

Format:

Decimal

Default value:

0

This combination of Conf ID and
Value configures Alarm 1 to wakeup
GS node from Standby mode or not.

• 0: Disable Alarm 1 wakeup
• 1: Enable Alarm 1 wakeup

Mandatory

1

Alarm 1 polarity

Value range:

0, 1

Format:

Decimal

Default value:

0

This combination of Conf ID and
Value specifies the polarity of the
transition at pin RTC_IO_1 of the
module which triggers an alarm input
and wakes up the GS node from
Standby.

• 0: high-to-low transition as active
• 1: low-to-high transition

Mandatory

2

Alarm 2 wakeup

Value range:

0, 1

Format:

Decimal

Default value:

0

This combination of Conf ID and
Value configures Alarm 2 to wakeup
GS node from Standby mode or not.

• 0: Disable Alarm 2 wakeup
• 1: Enable Alarm 2 wakeup

Mandatory

3

Alarm 2 polarity

Value range:

0, 1

Format:

Decimal

Default value:

0

This combination of Conf ID and
Value specifies the polarity of the
transition at pin RTC_IO_2 of the
module which triggers an alarm input
and wakes up the GS node from
Standby.

• 0: high-to-low transition as active
• 1: low-to-high transition

«
...
150
151
152
153
154
...
»

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS2101M Series

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: Canon Страницы: 2

Бренд: Garmin Страницы: 12

Бренд: BADLANDS Страницы: 2

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Samson Страницы: 20

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренд: brel-motors Страницы: 2

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: Watlow Страницы: 20

Бренд: TeleMann Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды