Главная
/
Telit Wireless Solutions
/
GS2101M Series
/
Справочник по командам

Telit Wireless Solutions GS2101M Series, Справочник по командам

Поделиться

Страница: 177 / 196

background image

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0 177

2019-08-05

Parameter Description

Table 153, page 177

describes the Live Calibration parameters.

Synchronous Response

Table 154, page 177

describes the synchronous responses and remarks for the Live

calibration command.

Example

AT+WLCALEN=1
OK

Table 153 Live Calibration Parameters

Parameter Optional/Mandatory

Value

Description

value

Mandatory

0, 1, ?
Default value - 1

0:Disables live calibration.
1:Enables live calibration.
?:Provides the current value of the live
calibration flag. Returns value 1 when live
calibration is enabled or return 0 when live
calibration is disabled.

Table 154 Live Calibration Synchronous Responses

Responses

Remarks

OK

Success

ERROR:INVALID INPUT

If parameters are not valid
(If value is other than 0, 1, or ? )

NOTE:

This command needs to be used with caution only during assembly and

manufacturing. The following steps need to be performed during assembly (if
required):
1.) Erase live calibration data.
2.) Once the system boots up, disable live calibration, as it is automatically
enabled when the system boots up.
3.) Live calibration is scheduled to start in the next boot based on the following
triggers:
- During scan
- In associated state
- Unsolicited Tx and unsolicited Rx
- RF commands or RF stop command
- Going to standby

«
...
175
176
177
178
179
...
»

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS2101M Series

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

Бренд: Quectel Страницы: 95

Бренд: ICAS Страницы: 51

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: IBP Страницы: 12

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: D+H Страницы: 32

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Бренд: JASTEC Страницы: 18

VARIOMATIC SARV 07.1

Бренд: AUMA Страницы: 32

Бренд: Chamberlain Страницы: 4

Бренд: Shimaden Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды