Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 174

Страница: 174 / 196

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0 174

2019-08-05

Table 151, page 174

describes the PHY Test Transmit Rates (TX100 mode).

AT+WTX100TEST=1,0,16,0,0,1,0,0,1,1,0,1,3,1

TestPatternType

Mandatory

0,1

Selects the test pattern to be transmitted.

• 0 - All 1s
• 1 - All 0s

PhyTestTxRate

Mandatory

0 to 7

The rate will differ depending on the
ModeSelect (see

Table 151, page 174

ModeSelect

Mandatory

0 to 2

• 0 - 11g mode
• 1 - 11b mode
• 2 - 11n mode

Table 150 Asynchronous Frame Transmission (TX100 mode) (Continued)

Parameter

Optional/Mandatory

Value

Description

Table 151 PHY Test Transmit Rates (TX100 mode)

Mode Select

PhyTestTxRate

Data Rate (Mbps)

5.5

MCS0

MCS1

MCS2

MCS3

MCS4

MCS5

MCS6

MCS7

NOTE:

Special equipment may need to be setup in order to observe the signals.

Содержание GS2101M Series





































































































































































































Результаты поиска

Содержание GS2101M Series

Отзывы:

Telit Wireless Solutions GS2101M Series, Справочник по командам, Страница: 174 / 196

Результаты поиска

Содержание GS2101M Series

Отзывы: