Главная
/
Telit Wireless Solutions
/
GS2101M Series
/
Справочник по командам

Telit Wireless Solutions GS2101M Series, Справочник по командам

Поделиться

Страница: 136 / 196

background image

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

136

2019-08-05

5.4.9 Invitation Procedures

This command is used to send an invitation request to the given peer address to join an
active group.

Command Syntax

AT+P2PINVITE=<peer p2p device MAC address><CR>

Usage

The invitation is sent to request the peer to join the group for which this device is a GO or
to request the peer to join the group for which the device address is specified.

Parameter Description

Table 114, page 136

describes the Invitation Procedures parameters.

Synchronous Response

Table 115, page 136

describes the synchronous responses and remarks for the Invitation

Procedure command.

Asynchronous Response

Table 116, page 137

describes the asynchronous responses and remarks for the Invitation

Procedure command.

NOTE:

This does not support sending invitation to invoke a persistent group.

Table 114 Invitation Procedures Parameters

Parameter

Description

Peer p2p device MAC
address

The address of the peer P2P device to which an invitation has
been sent. The address is saved by MCU.Timeout per invitation
request is 10 seconds with a maximum retries of 10

Table 115 Invitation Procedures Synchronous Responses

Events

Verbose mode

Non Verbose mode

Remarks

SUCCESS

<CR><LF>OK<CR><LF>

<CR><LF>0<CR><LF>

Successfully sent P2P invitation.

SUCCESS

<CR><LF>ERROR<CR><LF>

<CR><LF>1:<CR><LF>

Failure in sending invitation
request

Failure

<CR><LF>ERROR<SP>INVALID<SP>I
NPUT<CR><LF>

<CR><LF>2<CR><LF>

Parameters are invalid

«
...
134
135
136
137
138
...
»

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS2101M Series

Бренд: York Страницы: 20

Бренд: Watts Страницы: 24

Бренд: Xylem Страницы: 48

Бренд: Atari Страницы: 3

Бренд: Konig Страницы: 47

Бренд: Adaptec Страницы: 2

Бренд: Webasto Страницы: 12

Бренд: ICP DAS USA Страницы: 26

Бренд: National Instruments Страницы: 22

Бренд: Sensitron Страницы: 32

Бренд: FUHR Страницы: 20

Бренд: GCE Страницы: 13

Бренд: Leviton Страницы: 2

Бренд: TECH Страницы: 20

Бренд: Pro-face Страницы: 48

Бренд: Inovance Страницы: 2

Metso T2 Series

Бренд: Neles Страницы: 16

Бренд: C-TEC Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды