manualshive.com logo in svg

Telit Wireless Solutions GS2101M Series, Справочник по командам, Страница: 168 / 196

Поделиться
Скачать
Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 168

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

 Rev. 2.0                                                          168                                                          

 2019-08-05

8.1.1.9 Asynchronous Frame Transmission (TX99 mode)

This command is used to enable TX99 mode.

Command Syntax

AT+WTX99TEST=<Channel>,<BandWidth>,<NumFrames>,<FrameLen>
,<TxRate>,<TxPower>,<DestAddr>,<Bssid>,<GuardInterval>,
<GreenField>,<Antenna>,<Cca>,<Agc>,<ContPreambleMode>,
<Spreader>,<Scrambler>,<Preamble>,<PreambleType>,
<TestPatternType>,<PhyTestTxRate>,<ModeSelect>

Usage 

This command enables the asynchronous data transmission with the parameters configured.

Parameter Description

Table 147, page 168

 describes the Asynchronous Frame Transmission (TX99 mode) 

parameters.

NOTE:  

Issue AT+WRFTESTSTART command before issuing the FrameTX test 

or the TX99 test commands; otherwise a WLAN exception/reset will occur.

Table 147   Asynchronous Frame Transmission Parameters 

Parameter

Optional/Mandatory

Value

Description

Channel

Mandatory

1 to 14

The channel on which the data is to be 
sent (1-14).

BandWidth

Mandatory

0

The values of 0 is 20MHz.

Note: 

Currently the GS node supports only 20MHz operation.

NumFrames

Mandatory

1-65535

The number of asynchronous frames 
to be sent (1-65535).

Note: 

For continuous transmission, configure this parameter with the value 99.

FrameLen

Mandatory

32-1500

The length of the payload.

TxRate

Mandatory

0 to 7

• Non HT Rates - 0
• Ht Rate - 0 to 7 (MCS Index)

Note: 

Use PhyTestTxRate and ModeSelect fields to change the transmission rate.

TxPower

Mandatory

0 to 27

The value of this parameter can range 
from 0 to 27. Where 27 is the index 
corresponding to Maximum TxPower 
GS node will support.

DestAddr

Mandatory

N/A

The MAC address of the node targeted 
to reach.

BSSID

Mandatory

N/A

The MAC address of any arbitrary AP, 
which will be the source MAC 
address.

Содержание GS2101M Series





































































































































































































Отзывы:

Нет отзывов