Telex Azedit Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 182

background image

Telex Communications

131

Download Firmware Updates

Updating Master Controller Firmwaree

Warning!

The following procedure will cause one or more brief disruptions in intercom communications. Also, save

your intercom system configuration before proceeding.

From the File menu, select Save.

Later, if you need to restore the intercom configuration from disk, use Send File in the Online menu.

Master Controller Update: ADAM CS, ADAM Single Frame, ADAM DBX System, Zeus, Zeus II

Before you begin, be sure to verify that SERVER mode has been disabled. Also, it is very important to take the
Standby Controller card out of the frame, if one is installed.

Note: The Active Master Controller will have a red LED ON in the status LED window.

To update the master controller, do the following:

1. From the Status Menu, select Software Versions.

A popup list appears.

2. From the Software Versions popup list, select Master Controllers.

The Master Controller Version Information screen appears.

3. Right-click the active Master Controller, and then select Download Firmware.

The Firmware Download screen appears.

Note

: You can also press Ctrl+Shift+D to open the Download Firmware screen once the Master

Controller is highlighted.

4. From the Download Firmware screen, select the firmware update file.

5. Click Open.

The firmware update appears in the Download Firmware screen.

6. Click Begin Download.

This process can take from one to five minutes depending on the baud rate you have selected.

Note

: If there is any disruption in the communications link during the download, you will get an error

message. In this case, repeat the download.

7. When the file has been completely downloaded, the master controller will begin processing the

update.
IMPORTANT: Any disruption at this point, such as a loss of power, removing or resetting cards
(ADAM, ADAM CS, etc.) will result in Master Controller failure!

If this happens, you will either have to return the affected unit for replacement or you will have to
remove the EEPROM chip(s) from the affected unit and manually reprogram them with an
EEPROM programming tool.
ADAM and ADAM CS users do NOT proceed with the update of any more cards until you
identify the problem.

The AZedit session goes offline for 15-20 seconds when the card performs a reset. It automatically
will reconnect when it is finished.

M

«
...
129
130
131
132
133
...
»

Содержание Azedit























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Azedit

Бренд: Halcro Страницы: 12

850DP - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 2

Бренд: Adobe Страницы: 122

SECURITY THREAT RESPONSE MANAGER - LOG MANAGEMENT INSTALLATION REV 1

Бренд: Juniper Страницы: 30

ENTERPRISE VIRTUALIZATION FOR DESKTOPS

Бренд: Red Hat Страницы: 14

MOBILE SECURITY 6 FOR S60 -

Бренд: F-SECURE Страницы: 37

TROPOS SUPERSEARCH 2.4.0.000

Бренд: SSI Страницы: 8

FLASH 8-ACTIONSCRIPT 2.0 LANGUAGE

Бренд: MACROMEDIA Страницы: 1378

Modero NXD-1000Vi

Бренд: AMX Страницы: 2

CERTIFICATE SYSTEM 7.3 - ADMINISTRATION

Бренд: Red Hat Страницы: 554

Diabetes Management Software v2.2

Бренд: OneTouch Страницы: 13

15606-011408-9320 - MAP R6.3 CPU MODEL-UPG 4/5 MIN 2 CPUS INITL

Бренд: Autodesk Страницы: 190

15606-011408-9330 - MAPGUIDE R6.3 SITE LIC-UPG R6

Бренд: Autodesk Страницы: 94

Бренд: Bay Networks Страницы: 88

MAXIMO SG24-7645-00

Бренд: IBM Страницы: 152

Бренд: Tascam Страницы: 16

ThinkCentre A55

Бренд: Lenovo Страницы: 210

ThinkCentre A57

Бренд: Lenovo Страницы: 788

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды