TEC Electronics Prizrak 5S/BT, Техническое описание

Страница: 19 / 32

19
TEC-67398-2 Technical description Prizrak-5S BT
3
Pulse after «Disarming»
The output provides a pulse of 0,8 seconds upon arming the vehicle by the OEM remote
key (keyless entry system)
Yes
4
Pulse after authentication
The output generates a pulse signal of 0,8 seconds after the vehicle’s owner completes
an authentication procedure. Can be used for connection to a «lock» wire of an elec-
tro-mechanical hood lock and for other purposes.
Yes
5
Vehicle’s OEM alarm panic status
The output generates a constant level signal while the vehicle’s OEM alarm system is on
alert
Yes
6
Alert to a pager
A constant level signal of 30 sec is formed while the vehicle is «armed» and if any vehicle
compartment is violated (doors opened, hood, trunk). The signal disappears after the
vehicle is disarmed
Yes
7
Alert/warning pulses to the vehicle’s klaxon
A pulse signal is formed during 30 sec. if while in armed mode the vehicle’s perimeter is
violated (door/s opened, hood, trunk). The feature may be implemented on vehicle’s with -
out OEM alarm system. The potential disappears right after disarming the immobilizer. Is
used for connection to a vehicle’s klaxon
Yes
8
Doors, hood and trunk
A constant signal is formed when a pre-programmed door, hood or trunk is opened.
The programmig sequence is described above in chapter «Sequence for programming
inputs/outputs (menu 11)» starting from the step 5.
After the brake pedal is pressed. the immobilizer will indicate the current option value
twice in a row by the series of 8 beeps then short intermittent signals will follow. Release
the brake pedal. The immobilizer will keep emitting short intermittent signals.
6. To configure the value of another option-release the brake pedal. This will bring you
back to the step 3 of the programming sequence. To exit the programming mode - switch
the ignition OFF.
Open only those doors (you may do it beforehand) that are supposed to be indicated on
that output, the doors you don’t want to be indicated should be closed. Apply the brake
pedal again and keep it pressed, the immobilizer will emit 8 beeps — the doors are now
assigned to the output. If you don’t press the brake pedal and exit the programming menu
then the immobilizer will save in its memory the previouse option value
Yes
9
Sensors ignoring
A constant level signal is formed during the «Comfort» feature operation and when the
trunk is being released from the vehicle’s OEM remote
Yes
10
«Vehicle’s OEM button pressure» programming algorithm
A constant level signal signal is formed if a preprogrammed vehcle button is pressed.
Refer to the chapter «Sequence for programming inputs/outputs (menu 11)» starting
from the step 5.
After the brake pedal is pressed the immobilizer will indicate the current option value
twice in a row by a series of one long beep, and then will start emitting short intermittent
audible signals. Holding the brake pedal, press a desired button (please refer to the Inte -
grator to check the list of available buttons for a specific vehicle). If the the immobilizer
recognizes the button, it will stop emitting intermittent signals and will return to a current
option number indication by a series of 1 long beep. Release the brake pedal, the immo -
bilizer will start indicating a current option number. If you release the brake pedal before
the immobilizer has learned a button, it will exit this option, save previous option settings,
and will go back to a current option number indication
Yes
11
Ignition
A constant level signal is generated while the vehicle’s ignition is ON or the engine is
started. The signal will vanish as soon as the ignition is switched OFF
Yes
12
ACC
A constant level signal is formed while the vehicle’s accessories are ON (the first key po -
sition of the ignition switch may match with the ignition). The output stops generating a
signal as soon as the accessories (ACC) are switched off
Yes