TEC Electronics Prizrak 5S/BT, Техническое описание

Страница: 13 / 32

13
TEC-67398-2 Technical description Prizrak-5S BT
2nd step. Selecting and programming vehicle buttons
At this step is carried out selection and programming of the vehicle's buttons that are going to be used for enter -
ing a PIN code and for configuring the immobilizer settings. There is no need to program the vehicle's buttons if the
immobilizer is able to sense them via the CAN-bus (refer to the Integrator). You will need to connect to «wired but-
tons» and program them in case if a vehicle doesn't have buttons operating via CAN-bus (see description below).
It is allowed to use the «wired buttons» in addition to the «CAN buttons». The «wired buttons» must be pro-
grammed within 15 minutes after interfacing the immobilizer with a vehicle. You should reset the immobilizer to
de fault settings and repeat the interfacing procedure if you fail to program the buttons within 15 minutes.
Resistive buttons (are usually located on the steering wheel).
Connect the grey/yellow wire (output №7) to the resistive buttons circuit with positive polarity. Then connect
the grey/black wire (output 17) to the resistive buttons with negative polarity (refference ground). Make sure the
immobilizer is configured for operation with resistive buttons («Menu 10», option №6).
Programming sequence:
1. Switch ON the ignition and wait not less then 5 seconds.
2. Press and hold one by one (for approximately 2 sec) all steering wheel buttons and understeering switches
(cruise control and etc.). A button will not be programmed and it will not be possible to use it if the button
is released before the immobilizer emits a short beep. A short beep emitted when a button is being pressed
means that this button will be available for use as a PIN code button or one of the PIN code buttons.
3. Switch OFF the ignition, a confirmatory trill will sound.
4. Switch ON the ignition.
5. Assign one button as the programming button from the available ones by pressing that button and holding
it for at least 5 seconds until you hear a beep.
Positive or negative buttons (regular momentary-push buttons with NO terminals).
Connect any unused programmable inputs of the immobilizer to the vehicel's buttons of a corresponding po -
larity and assign the feature №6 (refer to the Table №7) to the programmable inputs. These buttons may be used
as the programming button or for entering a PIN code, even if the resistive or CAN type of buttons are used as well.
If you are going to connect the grey/yellow wire (input №7) and the grey/black wire (input №1) to a positive and/
or negative button, you will have to program them for operation with a positive and/or negative button (refer to the
«Menu 10», option №6). It is possible to change the setting of the option №6 only with the built-in programming
(reset) button until a PIN code is entered with a vehicle's button. Reset the module to default values, if you have
already entered a PIN code with a vehicle's button, in order to make changes in the option №6. If you need to assign
the programming button from among those buttons: turn ON the ignition, press and hold pressed the selected but -
ton for at least 5 seconds until you hear a beep.
3rd step. Configuring the Immobilizer features
At this point is carried out customization of the user features and adjustment of a new PIN code combination
and the immobilizer hardware features. The programming button allows to carry out all necessary adjustments in
accordance with the programming menu (the menus are shown below).
Table 4. Programming menu structure
Menu number Menu function
Code to
enter the
menu
Number of
confirmatory
beeps
Menu 10 Hardware features configuration 10 3
Menu 11 Programmable inputs/outputs configuration 11 6
Menu 12 Immobilizer custom settings 12 4
Menu 20 Hood comparment module HCU-230/BT configuration 20 10
It is recommended to program the immobilizer using a specially developed software «TECprog2» allowing to
save time for installation of the immobilizer and avoid accidental mistakes that may arise from manual program-
ming. The up to date «TECprog2» software version is available for download at https://tecel.ru/en/tecprog/
Connect the immobilizer to a computer via a micro-USB cable and update the fimware of the immobilizer, set
up a desired vehicle model, configure the immobilizer settings and features. The immobilizer may be connected to
a computer via Bluetooth, but for this purpose is required a special TECprog USB Bluetooth adapter. The Bluetooth
adapter allows configuring the settings and upgrading the firmware of the Immobilizer system.