LLEXETER.CO.UK
LLEXETER LTD - UNITS 15-18 GREENDALE BUSINESS PARK - WOODBURY SALTERTON - DEVON - EX5 1EW - UNITED KINGDOM
COMPANY NO: 4940600 / VAT REGISTRATION NO: GB825156925 TEL: 01395 233128
5.2 Diagnostic Codes
E09
00009
Over charge error
1. Charging voltage is higher than single battery cell's
over charge protection voltage 4250mV.
2. Misinformation of BMS
Discharge and recharge the battery
Re-start the bike
Error does not prevent riding but prevents
charging. After the re-start, if the error code
persists, replace the battery
E10
0000A
Level 1 over discharge error
E11
0000B
Level 2 over discharge error
E12
0000C
Level 1 over discharge current
error
Battery discharge current too high
Reduce power usage for 1 mile
Check condition of drivetrain including rear
brake, wheel and gearbox for seizure.
E13
0000D
Level 2 over discharge current
error
Battery discharge current too high
Reduce power usage for 1 mile
Check wiring and systems for short circuit
Check condition of drivetrain including rear
brake, wheel and gearbox for seizure. Check
wiring and systems for short circuit or failure
E14
0000E
Over charge current error
Charging current is too high
Check the charger for faults
Replace the charger and try again
Ensure battery is being charged from an
official Talaria charger for the model. Check
wiring and connections. If necessary, replace
the charger.
E15
0000F
Software start failure error
Electrical overload when connecting the battery
Please follow the owner's manual to turn on
the powertrain and start riding.
Ensure the ignition and circuit breaker are in
the "Off" position before connecting the
battery
E16
00010
Pre-charge time-out error
1. Failure of the charger or incorrect battery charger
2. BMS failure.
1. Replace the charger and try again
2. If 1. does not work, replace the battery
Ensure the correct battery charger is being used
and test with a replacement if necessary,
otherwise replace the battery.
E17
00020
MOS temperature sensor failure
error
MOS Temperature sensor failure
Re-start the bike
If the fault persists, replace the battery
E18
00030
Battery cell temperature sensor
failure error
Battery cell temperature sensor failure
Re-start the bike
If the fault persists, replace the battery
E19
00040
Battery discharge overheated
error
Battery overheating while being discharged
Stop riding and allow the battery to cool
before continuing to ride the machine
Check condition of drivetrain including rear
brake, wheel and gearbox for seizure. Check
wiring and systems for short circuit or failure
and ensure machine is not overloaded
E20
00050
Battery charge overheated error
Internal battery temperature too high while charging
Stop charging and allow the battery to cool
before attempting to charge the battery
Ensure the battery is being charged in a well
ventilated area at room temperature. Allow the
battery to cool before attempting to charge
E21
00060
Battery discharge low
temperature error
Internal battery temperature too low while riding
Stop riding and return the machine to a warm
area and wait for the internal temperature to
rise before continuing to use the machine
Stop riding and return the machine to a warm
area and wait for the internal temperature to
rise before continuing to use the machine. If
the fault persists when at the correct
temperature, replace the battery
E22
00070
Battery charge low temperature
error
Internal battery temperature too low while charging
Stop charging and return the battery to a warm
area and allow the internal temperature to rise
before charging
Stop charging and return the battery to a warm
area and allow the internal temperature to rise
before charging. If the fault persists when at
the correct temperature, replace the battery
E23
00080
Battery discharge, MOS
overheated error
It's caused by the overheated MOS when the battery pack
is discharging.
Stop riding the machine until the temperature
has lowered
Check condition of drivetrain including rear
brake, wheel and gearbox for seizure. Check
wiring and systems for short circuit or failure
and ensure machine is not overloaded
E24
00090
Battery charge, MOS overheated
error
It's caused by the overheated MOS when the battery pack
is charging.
Stop charging the battery until the temperature
has lowered
Ensure the battery is being charged in a well
ventilated area at room temperature. Allow the
battery to cool before attempting to charge
E25
000A0
Soft-start circuit overheated error
Soft start system overheating
Do not ride the machine until the overheat
protection has reset
Do not ride the machine until the overheat
protection has reset
E26
000B0
Storage error
Internal fault in the motor control unit
Send the bike to the nearest dealer to repair.
Check all wiring connections, battery
connections and wiring for faults and repair if
necessary. If fault persists, replace the
controller
E27
000C0
Discharge fuse failure error
Not applicable
/
E28
000D0
Charge fuse failure error
Not applicable
/
E29
000E0
Level 3 over current error
Short circuit in the electrical wiring
Inspect and eliminate the short circuit.
Test all wiring and connections for failure or
short circuit. Check motor phase coils for fault
or short circuit.
E30
000F0
Level 4 over current error
Short circuit in the electrical wiring
Inspect and eliminate the short circuit.
Test all wiring and connections for failure or
short circuit. Check motor phase coils for fault
or short circuit.
E31
00100
Setting error
Production fault in the motor controller
Replace the motor controller assy.
E33
00300
Controller phase wire over
current error
Controller phase wire current is equal or greater than the
protection value.
1. Turn off the bike, and switch off the circuit
breaker. Then, check the whether the motor
phase wire terminal are loose, or broken.
Check whether the motor outlet phase
sequence corresponds to the U / V / W on the
controller. Finally, check whether the
magnetic encoder output wire corresponds to
the yellow, green and blue wires on the
harness assembly.
2. Check the rear wheel and brake for
obstruction or seizure
Check motor phase wires and Hall sensors for
correct operation. If fault persists, replace the
motor
Battery charge too low
Charge the battery immediately.
Charge the battery immediately.
