manualshive.com logo in svg

Swan Analytical Instruments AMI Hydrazine, Руководство оператора, Страница: 80 / 86

Поделиться
Скачать
Swan Analytical Instruments AMI Hydrazine Скачать руководство пользователя страница 80

78

A-96.250.501 / 280915

AMI Hydrazine

Default Values

10. Default Values

Operation:

Sensors:

Filter Time Const.:..................................................................30 Sec

Hold after Cal.:.....................................................................300 Sec

Alarm Relay

...................................................................... same as in Installation

Relay 1 and 2

...................................................................... same as in Installation

Input

...................................................................... same as in Installation

Logger:

Logger Interval:..............................................................  30 Minutes

Clear Logger: ................................................................................no

Installation:

Sensors

Temp. comp.: .............................................................................. 3%

Signal Output 1

Parameter: ........................................................................Hydrazine

Current loop: .....................................................................4 –20 mA

Function: .................................................................................. linear
Scaling: Range low: ............................................................0.00 ppb

Scaling: Range high:.............................................................100ppb

Signal Output 2

Parameter: ....................................................................Temperature

Current loop: .....................................................................4 –20 mA

Function: .................................................................................. linear

Scaling: Range low: ................................................................0.0 °C

Scaling: Range high:.............................................................50.0 °C

Alarm Relay:

Alarm Hydrazine:
Alarm high:..........................................................................1000ppb

Alarm low: ...........................................................................0.00 ppb

Hysteresis: ..............................................................................10ppb
Delay:.......................................................................................5 Sec
Sample Flow; Flow Alarm ........................................................... yes

Sample Flow; Alarm high.....................................................300 rpm

Sample Flow; Alarm low ......................................................150 rpm

Sample Temp; Alarm high:.......................................................55 °C

Sample Temp; Alarm low: ..........................................................5 °C

Case temp. high:......................................................................65 °C

Case temp. low: .........................................................................0 °C

Relay 1 and 2

Function: .......................................................................... limit upper

Parameter: ........................................................................Hydrazine
Setpoint:.............................................................................1000 ppb

Hysteresis: .............................................................................10 ppb
Delay:.....................................................................................30 Sec

Содержание AMI Hydrazine























































































Отзывы:

Нет отзывов