manualshive.com logo in svg

Swan Analytical Instruments AMI Hydrazine, Руководство оператора, Страница: 67 / 86

Поделиться
Скачать
Swan Analytical Instruments AMI Hydrazine Скачать руководство пользователя страница 67

AMI Hydrazine

Program List and Explanations

A-96.250.501 / 280915

65

5 Installation

5.1 Sensors

5.1.1

Temp Comp

Temperature compensation in %. 
Range: 0.0–5.0%

5.2 Signal Outputs

Note: 

The navigation in the menu <Signal Output 1> and 

<Signal Output 2> is identical. For reason of simplicity only the 
menu numbers of Signal Output 1 are used in the following.

5.2.1 and 5.2.2

Signal Output 1 and 2:

 Assign process value, the current loop 

range and a function to each signal output.

5.2.1.1

Parameter:

 Assign one of the process values to the signal output.

Available values:

Hydrazine

Temperature

Sample Flow

5.2.1.2

Current Loop:

 Select the current range of the signal output. Make 

sure the connected device works with the same current range.

Available ranges: 0–20 mA or 4–20 mA

5.2.1.3

Function:

 Define if the signal output is used to transmit a process 

value or to drive a control unit. Available functions are:

Linear, bilinear or logarithmic for process values.

See 

As process values, p. 66

Control upwards or control downwards for controllers.

See 

As control output, p. 67

Содержание AMI Hydrazine























































































Отзывы:

Нет отзывов