manualshive.com logo in svg

Swan Analytical Instruments AMI Hydrazine, Руководство оператора, Страница: 64 / 86

Поделиться
Скачать
Swan Analytical Instruments AMI Hydrazine Скачать руководство пользователя страница 64

62

A-96.250.501 / 280915

AMI Hydrazine

Program List and Explanations

2.2.2

Miscellaneous

:

2.2.2.1

Case Temp:

 Shows the actual temperature in °C inside the trans-

mitter.

2.3 Sample

2.3.1



Sample ID

:

 Shows the assigned sample identification. This 

identification is defined by the user to identify the location of the 

sample



Temperature: 

Shows temperature in °C.

(Nt5K)

: Shows raw value of the temperature in 





Sample Flow:

 Shows the sample Flow in rpm

(Raw value)

 Shows the sample Flow in Hz

2.4 I/O State

Shows actual status of all in- and outputs.

2.4.1

2.5 Interface

Only available if optional interface is installed.

Review programmed communication settings.



Alarm Relay

:

Open or closed.



Relay 1 and 2

: 

Open or closed.



Input

: 

Open or closed.



Signal Output 1 and 2

: 

Actual current in mA



Signal Output 3 (option)

:

Actual current in mA

Содержание AMI Hydrazine























































































Отзывы:

Нет отзывов