manualshive.com logo in svg

Swan Analytical Instruments AMI Hydrazine, Руководство оператора, Страница: 70 / 86

Поделиться
Скачать
Swan Analytical Instruments AMI Hydrazine Скачать руководство пользователя страница 70

68

A-96.250.501 / 280915

AMI Hydrazine

Program List and Explanations

If Control upwards or Control downwards is active

Setpoint:

 User-defined process value (Measured value or flow)

P-Band:

 Range below (upwards control) or above (downwards 

control) the set-point, within the dosing intensity is reduced from 

100% to 0% to reach the set-point without overshooting.

5.2.1.43

Control Parameters:

 if Parameter = Hydrazine

5.2.1.43.10

Setpoint

Range: 0.00–1000 ppb

5.2.1.43.20

P-Band

Range:0.00–1000 ppb

5.2.1.43

Control Parameters:

 if Parameter = Temperature

5.2.1.43.11

Setpoint

Range: -30 to +120 °C

5.2.1.43.21

P-Band

Range: 0 to +100 °C

5.2.1.43

Control Parameters:

 if Parameter = Sample Flow

5.2.1.43.12

Setpoint

Range: 0–300 rpm

5.2.1.43.22

P-Band

Range: 0–300 rpm

5.2.1.43.3

Reset time:

 The reset time is the time till the step response of a sin-

gle I-controller will reach the same value as it will be suddenly 

reached by a P-controller.

Range: 0–9’000 sec

5.2.1.43.4

Derivative time:

 The derivative time is the time till the ramp re-

sponse of a single P-controller will reach the same value as it will 

be suddenly reached by a D-controller.

Range: 0–9’000 sec

5.2.1.43.5

Control timeout:

 If a controller action (dosing intensity) is constantly 

over 90% during a defined period of time and the process value 

does not come closer to the setpoint, the dosing process will be 

stopped for safety reasons.

Range: 0–720 min

Содержание AMI Hydrazine























































































Отзывы:

Нет отзывов