Swan Analytical Instruments AMI Hydrazine Скачать руководство пользователя страница 47

Страница: 47 / 86

AMI Hydrazine

Maintenance

A-96.250.501 / 280915

6.8.

Changing the Diffusion Tube

Shut down the instrument as described in

Stop of Operation for

Maintenance, p. 36

Consider the Warning concerning Diisopropylamine handling.

The correct measuring value will appear after 30 min of continuous

operation (flow and power on). Diisopropylamine needs roughly

30 min to penetrate the walls of the new diffusion tube.

Fill roughly 750 ml high purity water into a 1 l bea-

ker.

Unscrew and remove Diisopropylamine bottle

from the holder.

Close the bottle immediately.

Remove the old diffusion tube from the steel

tubes.

Dip the new diffusion tube into the beaker filled

with high purity water and rinse it some seconds.

Push the new diffusion tube over the steel tubes.

Open the reagent bottle and slide it over the diffu-

sions tube.

Note:

Ensure that the diffusions tube lies pretzel-

shaped in the reagent bottle as shown in the
picture.

Screw the bottle into the holder.

Содержание AMI Hydrazine























































































Результаты поиска

Содержание AMI Hydrazine

Отзывы:

Swan Analytical Instruments AMI Hydrazine, Руководство оператора, Страница: 47 / 86

Результаты поиска

Содержание AMI Hydrazine

Отзывы: