Supero AS-1010S-T Скачать руководство пользователя

Страница: 51 / 100

Chapter 5: Advanced Motherboard Setup

5-17

IPMI Header

The Intelligent Platform Management

Interface (IPMI) header is located at

J5. Connect the appropriate cable

here to utilize IPMB on your system.

See the table on the right for pin

deﬁ nitions.

IPMI

Pin Deﬁ nitions (J5)

Pin# Deﬁ nition

Data

Ground

Clock

N/A

LAN1/2 (Ethernet Ports)

Two Gigabit Ethernet ports (desig-

nated LAN1 and LAN2) are located

beside the VGA port. These ports

accept RJ45 type cables.

Power Supply Fail Alarm
Header

Connect a cable from your power

supply to JP1 to provide you with

warning of a power supply failure.

The warning signal is passed through

the PWR_LED pin to indicate a power

failure. See the table on the right for

pin deﬁ nitions.

Power Supply Fail

Alarm Header

Pin Deﬁ nitions (JP1)

Pin# Deﬁ nition

P/S 1 Fail Signal

P/S 2 Fail Signal

Reset (from MB)

Note:

This feature is only available when using

redundant power supplies.

Power Supply Fail Alarm
Reset Header

Connect JP11 to the alarm reset but-

ton on your chassis (if available) or to

a microswitch to allow you to turn off

the alarm that sounds when a power

supply module fails. See the table on

the right for pin deﬁ nitions.

Alarm Reset Header

Pin Deﬁ nitions (JP11)

Pin# Deﬁ nition

Ground

Reset Signal

Chassis Intrusion

A Chassis Intrusion header is located

at JL1. Attach the appropriate cable

to inform you of a chassis intrusion.

Chassis Intrusion

Pin Deﬁ nitions (JL1)

Pin# Deﬁ nition

Intrusion Input

Ground

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды