Supero AS-1010S-T Скачать руководство пользователя

Страница: 36 / 100

5-2

AS1010S-T User's Manual

5-3 Processor and Heatsink Installation

Installing the Processor

1. Lift the lever on the CPU socket until

it points straight up.

Exercise extreme caution when handling and installing the proces-

sor. Always connect the power cord last and always remove it be-

fore adding, removing or changing any hardware components.

5-2 Mounting the Motherboard into a Chassis

All serverboards and motherboards have standard mounting holes to ﬁ t different

types of chassis. Make sure that the locations of all the mounting holes for both

the motherboard and the chassis match. Although a chassis may have both plastic

and metal mounting fasteners, metal ones are highly recommended because they

ground the motherboard to the chassis. Make sure that the metal standoffs click

in or are screwed in tightly.

1. Check the compatibility of the motherboard ports and the I/O shield

The H8SSL-i motherboard requires a chassis that can support extended ATX

boards of 8" x 12" in size, such as the SC811FT-260. Make sure that the I/O ports

on the motherboard align with their respective holes in the I/O shield at the rear

of the chassis.

2. Mounting the motherboard onto the mainboard tray in the chassis

Carefully mount the motherboard onto the mainboard tray by aligning the mother-

board mounting holes with the raised metal standoffs in the tray. Insert screws into

all the mounting holes in the motherboard that line up with the standoffs. Then use a

screwdriver to secure the motherboard to the mainboard tray - tighten until just snug

(if too tight you might strip the threads). Metal screws provide an electrical contact

to the motherboard ground to provide a continuous ground for the system.

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды