Supero AS-1010S-T Скачать руководство пользователя

Страница: 74 / 100

7-4

AS1010S-T User's Manual

PIO Mode

PIO (Programmable I/O) mode programs timing cycles between the IDE drive

and the programmable IDE controller. As the PIO mode increases, the cycle

time decreases. The options are

Auto

, 0, 1, 2, 3, and 4. Select Auto to allow

AMI BIOS to auto detect the PIO mode. Use this value if the IDE disk drive

support cannot be determined. Select 0 to allow AMI BIOS to use PIO mode

0. It has a data transfer rate of 3.3 MBs. Select 1 to allow AMI BIOS to use

PIO mode 1. It has a data transfer rate of 5.2 MBs. Select 2 to allow AMI

BIOS to use PIO mode 2. It has a data transfer rate of 8.3 MBs. Select 3 to

allow AMI BIOS to use PIO mode 3. It has a data transfer rate of 11.1 MBs.

Select 4 to allow AMI BIOS to use PIO mode 4. It has a data transfer rate of

16.6 MBs. This setting generally works with all hard disk drives manufactured

after 1999. For other disk drives, such as IDE CD-ROM drives, check the

speciﬁ cations of the drive.

DMA Mode

Select the DMA mode of the drive. Options are SWDMA0, SWDMA1, SWD-

MA2, MWDMA0, MWDMA1, MWDMA2, UDMA0, UDMA1 and UDMA2.

S.M.A.R.T.

Self-Monitoring Analysis and Reporting Technology (SMART) can help predict

impending drive failures. Select "Auto" to allow BIOS to auto detect hard

disk drive support. Select "Disabled" to prevent AMI BIOS from using the

S.M.A.R.T. Select "Enabled" to allow AMI BIOS to use the S.M.A.R.T. to sup-

port hard drive disk. The options are Disabled, Enabled, and

Auto

32-Bit Data Transfer

Select "Enabled" to activate the function of 32-Bit data transfer. Select "Dis-

abled" to deactivate the function. The options are Enabled and

Disabled

Hard Disk Write Protect

Select Enabled to enable the function of Hard Disk Write Protect to prevent data

from being written to HDD. The options are Enabled or

Disabled

IDE Detect Time Out (Sec)

This feature allows the user to set the time-out value for detecting ATA, ATA PI

devices installed in the system. The options are 0 (sec), 5, 10, 15, 20, 25, 30

and

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды