Supero AS-1010S-T Скачать руководство пользователя

Страница: 39 / 100

Chapter 5: Advanced Motherboard Setup

5-5

5-4 Connecting

Cables

Now that the processors are installed, the next step is to connect the cables to

the motherboard. These include the data (ribbon) cables for the peripherals and

control panel and the power cables.

Connecting Data Cables

The ribbon cables used to transfer data from the peripheral devices have been

carefully routed in preconﬁ gured systems to prevent them from blocking the ﬂ ow

of cooling air that moves through the system from front to back. If you need to

disconnect any of these cables, you should take care to reroute them as they

were originally after reconnecting them (make sure the red wires connect to the

pin 1 locations). If you are conﬁ guring the system, keep the airﬂ ow in mind when

routing the cables. The following data cables (with their motherboard connector

locations noted) should be connected. See the motherboard layout diagram in

this chapter for connector locations.

CD-ROM cable (IDE#1)

Floppy Drive cable (Floppy)

SATA cable (SATA0, SATA1)

Control Panel cable (JF1, see next page)

Connecting Power Cables

The H8SSL-i has a 24-pin primary power supply connector "PW1" for connection to

the ATX power supply. Connect the appropriate connector from the power supply

to the "ATX Power" connector to supply power to the motherboard. See the Con-

nector Deﬁ nitions section in this chapter for power connector pin deﬁ nitions.

In addition, your power supply must be connected to the Secondary ATX Power

connection at PW2.

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды