Supero AS-1010S-T Скачать руководство пользователя

Страница: 50 / 100

5-16

AS1010S-T User's Manual

ATX PS/2 Keyboard and
PS/2 Mouse Ports

The ATX PS/2 keyboard and the PS/2

mouse ports are located beside the

USB ports. See the table on the right

for pin deﬁ nitions.

Power LED/Speaker

On JD1, pins 1, 2, and 3 are for the

power LED and pins 4 through 7 are

for the speaker. See the tables on the

right for pin deﬁ nitions.

Note:

The speaker connector pins are

for use with an external speaker. If

you wish to use the onboard speaker,

you should close pins 6 and 7 with a

jumper.

Speaker Connector

Pin Deﬁ nitions (JD1)

Pin# Deﬁ nition

Red wire, Speaker data

No connection

Buzzer signal

Speaker data

Wake-On-Ring

The Wake-On-Ring header is desig-

nated JWOR. This function allows

your computer to receive and "wake-

up" by an incoming call to the modem

when in suspend state. See the table

on the right for pin deﬁ nitions. You

must have a Wake-On-Ring card and

cable to use this feature.

Wake-On-Ring

Pin Deﬁ nitions

(JWOR)

Pin# Deﬁ nition

Ground (Black)

Wake-up

PS/2 Keyboard and Mouse Port

Pin Deﬁ nitions

(J1)

Pin # Deﬁ nition

Data

VCC

Clock

Ground

PWR LED Connector

Pin Deﬁ nitions (JD1)

Pin# Deﬁ nition

+Vcc

Control

Wake-On-LAN

The Wake-On-LAN header is desig-

nated JWOL. See the table on the

right for pin deﬁ nitions. You must

have a LAN card with a Wake-On-LAN

connector and cable to use the Wake-

On-LAN feature.

Wake-On-LAN

Pin Deﬁ nitions

(JWOL)

Pin# Deﬁ nition

+5V Standby

Ground

Wake-up

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды