Supero AS-1010S-T Скачать руководство пользователя

Страница: 81 / 100

Chapter 7: BIOS

7-11

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. Disable Legacy support

if there are no USB devices installed in the system. The options are

Enabled

and Disabled.

USB 2.0 Controller Mode

Select the controller mode for your USB ports. Options are HiSpeed and

FullSpeed

. (HiSpeed=480 Mbps, FullSpeed=12 Mbps

)

BIOS EHCI Hand-Off

Enable

or Disable a workaround for OS's without EHCI hand-off support.

System Health Monitor

CPU Overheat Temperature

Use the "+" and "-" keys to set the CPU temperature threshold to between 65

and 90

C. When this threshold is exceeded, the overheat LED on the chas-

sis will light up and an alarm will sound. The LED and alarm will turn off once

the CPU temperature has dropped to 5 degrees below the threshold set. The

default setting is

The other items in the submenu are all systems monitor displays for the follow-

ing information:

System Temperature, CPU1 Vcore, +5 Vin, +12Vin, -12V Vcc, DRAM VTT, 1.2V

for Hyper-Transport, 5V standby, 2.5V standby and battery voltage.

System Fan Monitor

Fan Speed Control Modes

This feature allows the user to determine how the system will control the speed

of the onboard fans. If the option is set to "3-pin fan", the fan speed is controlled

based upon the CPU die temperature. When the CPU die temperature is higher,

the fan speed will be higher as well. If the option is set to "4-pin", the fan speed

will be controlled by the Thermal Management Settings pre-conﬁ gured by the

user with this setting. Select "3-pin" if your chassis came with 3-pin fan headers.

Select "4-pin" if your chassis came with 4-pin fan headers. Select "Workstation"

if your system is used as a Workstation. Select "Server" if your system is used

as a Server. Select "Disable" to disable the fan speed control function to allow

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды