Supero AS-1010S-T Скачать руководство пользователя

Страница: 97 / 100

C-1

Appendix C: System Speciﬁ cations

Appendix C

System Speciﬁ cations

Processors

Single AMD Opteron Series 100 processor in a 939-pin socket

Note: Please refer to our web site for a complete listing of supported processors.

Chipset

ServerWorks HT-1000 chipset

BIOS

4 Mb AMI BIOS

Flash ROM

Memory Capacity

Four 184-pin DIMM sockets supporting up to 4 GB of unbuffered ECC DDR400/333

low-proﬁ le SDRAM

Note: See the memory section in Chapter 5 for details.

Serial ATA Controller

ServerWorks on-chip controller

SATA/IDE Drive Bays

Two (2) hot-swap drive bays for 3.5" hard drives (hot-swap for SATA only)

Peripheral Drive Bays

One (1) ﬂ oppy drive

One (1) slim CD-ROM drive

Expansion Slots

(provided with included riser card)

One (1) riser card to support the use of one full height, half-length 133/100MHz

64-bit PCI-X expansion card

Motherboard

Model: H8SSL-i (ATX form factor)

Dimensions: 8 x 12 in (203 x 305 mm)

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды