Supero AS-1010S-T Скачать руководство пользователя

Страница: 82 / 100

7-12

AS1010S-T User's Manual

the onboard fans to continuously run at full speed (12V). The options are 1)

Disable, Full Speed

2) 3-pin (Server)

and 3) 3-pin (Workstation).

FAN1 Speed through FAN5 Speed

The speeds of the onboard fans (in rpm) are displayed here.

7-4 Boot

Menu

Boot Settings Conﬁ guration

Quick Boot

If Enabled, this option will skip certain tests during POST to reduce the time

needed for the system to boot up. The options are

Enabled

and Disabled.

Quiet Boot

Disabled

, normal POST messages will be displayed on boot-up. If Enabled,

this display the OEM logo instead of POST messages.

Add-On ROM Display Mode

This setting controls the display of add-on ROM (read-only memory) messages.

Select "

Force BIOS

" to allow the computer system to force a third party BIOS to

display during system boot. Select "Keep Current" to allow the computer system

to display the BIOS information during system boot.

Boot up Num-Lock

Set this to "On" to allow the Number Lock setting to be modiﬁ ed during boot up.

The options are

and Off.

PS/2 Mouse Support

This setting is to specify PS/2 mouse support.

The options are

Auto

, Enabled

and Disabled.

Wait for ‘F1’ If Error

Enable to activate the Wait for F1 if Error function. The options are

Enabled

and Disabled.

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды