Supero AS-1010S-T Скачать руководство пользователя страница 3

Страница: 3 / 100

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the AS1010S-T server. Installa-

tion and maintainance should be performed by experienced technicians only.

The AS1010S-T is a high-end server based on the SC811FT-260 1U rackmount

chassis and the H8SSL-i, a single processor motherboard that supports AMD Op-

teron processors and up to 4 GB of unbuffered ECC DDR400/333 SDRAM.

Manual Organization

Chapter 1: Introduction

The ﬁ rst chapter provides a checklist of the main components included with the

server system and describes the main features of the H8SSL-i motherboard and

the SC811FT-260 chassis, which comprise the 1010S-T.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the 1010S-T into a rack and

check out the server conﬁ guration prior to powering up the system. If your server

was ordered without processor and memory components, this chapter will refer you

to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Бренды по названию

Популярные бренды