Supero AS-1010S-T Скачать руководство пользователя

Страница: 58 / 100

5-24

AS1010S-T User's Manual

5-13 Enabling SATA RAID

Now that the hardware is set up, you must now install the operating system and

the SATA RAID drivers, if you wish to use RAID with your SATA drives. The

installation procedure differs depending on whether you wish to have the operating

system installed on a RAID array or on a separate non-RAID, IDE drive. See the

instructions below for details.

Serial ATA (SATA)

Serial ATA (SATA) is a physical storage interface that employs a single cable with a

minimum of four wires to create a point-to-point connection between devices. This

connection is a serial link that supports a SATA transfer rate from 150 MBps. The

serial cables used in SATA are thinner than the traditional cables used in Parallel

ATA (PATA) and can extend up to one meter in length, compared to only 40 cm for

PATA cables. Overall, SATA provides better functionality than PATA.

Installing the OS/SATA Driver

Before installing the OS (operating system) and SATA RAID driver, you must decide

if you wish to have the operating system installed as part of a bootable RAID array

or installed to a separate non-RAID, IDE hard drive. If on a separate IDE drive, skip

ahead to section entitled Enabling SATA RAID in the BIOS. If you wish to have the

OS on a SATA RAID array, you must ﬁ rst complete the step below.

Building

Driver

Diskette

You must ﬁ rst build a driver diskette from the Super Micro CD-ROM that was includ-

ed with the system. (You will have to create this disk on a computer that is already

running and with the OS installed. Note that this driver only works with Windows

2003. After building the driver diskette, insert the driver ﬂ oppy into the ﬂ oppy drive

in your system (must be an IDE ﬂ oppy and not a USB ﬂ oppy) and insert the OS

Installation CD into your CD-ROM or DVD drive. Boot up the system and press the

<F6> key. You will then be able to create a partition on the disk where the OS will

be installed. After the OS is installed the system will automatically roboot. You can

now skip ahead to section entitled Enabling SATA RAID in the BIOS.

Installing the Operating System

If the operating system has not yet been installed, you should install it now. With

the Windows OS installation CD in the CD-ROM drive, restart the system. When

you see the prompt, hit the <F6> key to enter Windows setup. Follow the prompts

as they appear to install the OS. Once installed, proceed to the next step to enable

RAID and set up your RAID drives.

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды