Supero AS-1010S-T Скачать руководство пользователя

Страница: 43 / 100

Chapter 5: Advanced Motherboard Setup

5-9

5-7 Adding

PCI

Cards

PCI slots:

The H8SSL-i has three PCI expansion slots. One of these slots (the 133 MHz PCI-

X slot #6) may be populated with the use of the CSE-RR1U-X riser card, which is

included with the system. You may install either a 133 or a 100 MHz PCI-X card

into the riser card.

PCI card installation:

Before installing a PCI add-on card, make sure it is supported by the riser card (see

step 1, above). Begin by pulling the locking tab downward to unlock the bracket

that covers the slot, then remove the bracket. Insert the PCI card into the riser

card, pushing down with your thumbs evenly on both sides of the card. When the

card is correctly installed, ﬁ nish by pushing the locking tab upward to secure the

card in the system.

Note:

the PCI slot shield helps promote proper airlow in the chassis and shield the

inside of the system from EMI (electromagnetic interference). For these reasons,

make sure there is a shield covering the slot if unused.

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды